Side Ads

Sunday, July 19, 2015

,

Motorola 2310-51 Business Single User VDSL Modem

This device is supplied to video digital subscriber line (VDSL)-eligible business customers who request high speed Internet (HSI) service and prefer the basic functionality of a modem vs. a gateway. When ordering VDSL-based service, business customers are provided with U-verse HSI service, but do not receive U-verse TV or U-verse Voice at that time.

Business customers must purchase their customer premises equipment (CPE), which includes a 30-day buyer's remorse (BRE) period and a one-year warranty for their CPE.
Note: The Motorola 2310-51 VDSL Modem is a standalone modem and cannot be accessed through tools such as CMS, MDC, and GUI.

Specifications 
  • The modem access code is on the yellow sticker on the bottom of the modem.
  • The serial number is on the white sticker on the bottom of the modem.
  • WAN interface.
  • 10/100 Ethernet RJ-45.
  • AT&T 7.8.7r17 firmware.
    • Firmware does not support IP Passthrough.
  • Small/light enclosure.
  • Wall-mountable.
  • Color-coded ports.
  • Five diagnostic LEDs including an Internet LED.
  • Customers can access the modem GUI by browsing to http://192.168.1.254.
  • The reset button is located on the back of the 2310.
  • 802.1x authentication.
Notes: 
  • The VDSL 2310 Motorola Modem firmware (7.8.7r17) is used for VDSL business customers. 
  • The Motorola 2310 does not support static IPs. 




Installation  
Installation of this device is accomplished via full-technician installation. 
Remove or Disable Conflicting Applications
Internet-sharing software and PC-based firewall applications typically interfere with the modem and should be removed or disabled before installing the modem. The modem provides the same features as the products listed below. If any of the following or similar applications are installed on the computers, remove or disable them according to the manufacturer's instructions before proceeding. 
  • Internet-sharing applications: Microsoft Internet Connection Sharing, Intel Anypoint ISS, and 3Com HomeClick
  • Proxy software: Wingate and Sygate
  • Security software: Norton Internet Security, Black Ice, and Zone Alarm
Check the Computer's Browser and System Requirements
Verify that the computers meet the following minimum requirements:
  • Browser requirements:
    • Windows: Microsoft Internet Explorer 5.5 or higher, Netscape Navigator 4.7 or higher, or Firefox 1.0 or higher
    • Macintosh: Safari 1.0, Microsoft Internet Explorer 5.0, or Netscape 4.74 or higher
  • System requirements:
    • Microsoft Windows 7, Windows Vista, Windows XP, Windows 2000, Windows NT 4.0 with Service Pack 6, Windows ME, Windows 98/98SE, or Mac OS 8.6 or higher
    • Ethernet adapter
While the browsers and operating systems (OS) listed above do meet minimum requirements, not all browsers and OS listed fall within AT&T scope of support. Refer customers with browsers and OS versions that are not in our scope of support to Tech 360 at 866-442-2827.

Choose a Computer and Location

Typically, the computer is located in the same room as the modem and the U-verse connection. Ethernet is the only connection method between the computer and the modem. Connect the computer to the modem. Save and close all open programs before beginning this process.

Note: Previous DSL customers may already have the filters referenced in the rest of this article already installed.

Filter Installation
Regular telephone and U-verse HSI signals are carried over the same line. Converting a regular telephone line to U-verse can cause high-pitched tones and static when using the phone. Installing a filter on every telephone or telephone device sharing the same telephone number as the U-verse HSI separates these signals and eliminates the noise. Do not install filters if the telephone line is only carrying a U-verse HSI signal.
Install the U-verse HSI Filter
  1. Locate the phone jack where the modem will be located.
  2. Insert the U-verse HSI filter into the jack.
  3. If there is a phone, answering machine, fax machine, satellite TV equipment, or other phone device in this jack location, plug it into the filter port labeled Phone.
  4. Install a filter on all other phone devices in the house (such as dial-up modems, fax machines, caller ID devices, and set-top boxes). Plug each of these devices into the filter port labeled Phone.
Wall-Mounted Phones
  1. Lift the telephone from the wall pegs and disconnect the phone cord from the wall jack.
  2. Connect the telephone cord from the back of the filter into the wall jack. Align the keyhole slots on the filter with the wall plate pegs and press down gently to secure.
  3. Connect the telephone cord to the phone jack located on the front of the mounted filter.
  4. Attach the telephone to the mounting pegs on the filter.
Ethernet Connection
  1. Connect the dual-port phone filter to their wall jack.
    • Phone service is not required to set up high speed Internet.
  2. If customer has a phone device that shares this jack, plug it into the port labeled Phone on the dual-port phone filter.
  3. Connect the green data cable from the port labeled DSL on the dual-port filter to the phone line port on the modem.
  4. Connect the yellow Ethernet cable from an Ethernet port on the modem to the Ethernet port on the PC.
  5. Connect one end of the power adapter to the power port on the modem and plug the other end into an electrical outlet.
    • A blinking, then steady green power light indicates a successful power connection.
  6. Check the connections:
    • With the computer completely started, verify the power and Ethernet indicator lights on the front of the modem are green. The Internet indicator light does not turn green until the modem software is installed and an Internet connection is established.
Note: A customer can have up to five communication devices at a time once in-house filters are installed.
First-time Power-up/Boot-up and Any Subsequent Factory Resets
Modem LED Sequencing and Timing
Inform the customer that during the first-time boot-up process, the modem automatically reboots. Customer interaction during this time is not necessary.
Boot Strap (First Contact with CMS) 
  1. On boot-up, the Power LED is green for two seconds, blinks red for one second, and then goes solid green. All other LEDs are off.
  2. After Power LED is solid green, DSL LED starts flashing red for approximately 4-6 seconds, flashes green for approximately 45 seconds, and goes solid green after ADSL line is up. While DSL is flashing red, Ethernet LED starts blinking green when a LAN device is connected to the Ethernet port. The Ethernet LED blinks green when traffic is received on the Ethernet port.
  3. After the DSL LED is solid green, the Internet LED starts flashing green for approximately 4-5 seconds (802.1x authentication and IP connectivity takes place).
  4. At the same time the Internet LED starts flashing green, the Activity LED starts blinking green. Activity LED continues to blink green when activity is seen from the broadband connection.
Reboot (CMS Issues the Reboot via 2310 Work Flow Modification 28-30 seconds after the bootstrap)
  1. On boot-up, the Power LED is green for two seconds, blinks red for one second, and then goes solid green. All other LEDs are off.
  2. DSL Power LED is solid green. DSL LED starts flashing red for approximately 4-6 seconds, flashes green for approximately 45 seconds, and then goes solid green after ADSL line is up. While DSL is flashing red, Ethernet LED starts blinking green when a LAN device is connected. The Ethernet LED blinks green when traffic is received on the Ethernet port.
  3. After DSL LED is solid green, Internet LED starts flashing green for approximately 4-5 seconds (802.1x authentication and IP connectivity takes place).
  4. At the same time the Internet LED starts flashing green, the Activity LED starts blinking green. Activity LED continues to blink green when activity is seen from the broadband connection.


LED Lights
LightLight StatusOperating State
Power LightOffThe modem is not getting power. Check that all connections are firmly plugged.
Solid greenPower is on.
Flash redThe modem is performing a self-test or receiving an upgrade.
Solid redSystem error
Ethernet LightOffThe modem is powered off or booting up.
Solid greenDevice(s) connected via ethernet, USB, or wireless.
DSL LightOffThe modem is powered off.
Flashing greenThe modem is attempting to establish a connection to the broadband service.
Flashing green then redThe modem has been unable to connect after three attempts.
Solid greenThe modem is fully connected to the broadband service.
Internet LightOffThe modem has been unable to detect a DSL signal or is powered off.
Flashing greenThe modem is attempting to establish a connection to the broadband service.
Solid greenThe modem is connected to the Internet.
Solid redThe modem cannot connect to the broadband service.
Activity LightOffThe modem has been unable to detect a DSL signal or is powered off.
Flashing greenThe modem is connected to the Internet and transmitting data.
Flashing redThe modem is attempting to establish a connection to the broadband service.
Solid redThe modem cannot connect to the broadband service.


Troubleshooting Tips
  • The Motorola 2310 modem is not as robust as the 2701, 3600, and 3800 RGs, therefore troubleshooting is not robust. The 2310 supports HSIA only, with very limited programming and capabilities; troubleshooting is limited to the modem functionality.
  • Troubleshooting is limited to determining if equipment is defective.

IP-DSL: 2Wire 2701HGV-B Gateway

This article provides a product overview of the IP-DSL 2701HGV-B Gateway, along with configuration and troubleshooting information for U-verse agents trained to support IP-DSL customers.

The 2Wire 2701 HGV-B is not shipped with new IP-DSL orders. It is used in like-for-like replacements of devices that are still under warranty.
Note: IP-DSL customers must purchase their IP-DSL CPE, which has a 30-day buyer's remorse (BRE) period and a one-year warranty.

Features 
  • Firmware Version 6.3.15.2 - Supports the U-verse features, which includes IGMP, 802.1x, captive portal, TR-98 and extensions, Quality of Service (QoS), and AT&T Voice over Internet Protocol (VoIP) support.
  • Not HPNA-compatible.
  • Not USB-compatible.
  • Support and GUI is the same as that of the 2701HG minus the point of protocol over Ethernet (PPPoE) configuration.
  • The Reset button is located on the back of this unit.
  • Uses the Motive CD-Less registration flow.
  • Uses 802.1x.
  • Four Ethernet Ports, Wi-Fi, and VoIP ATA.
Product Images

Installation 
Remove or Disable Conflicting Applications
Internet-sharing software and PC-based firewall applications typically interfere with the gateway and should be removed or disabled before installing the gateway. The gateway provides the same features as the products listed below. If any of the following, or similar, applications are installed on the computers, remove or disable them according to the manufacturer's instructions before proceeding.
  • Internet-sharing applications - Microsoft Internet Connection Sharing, Intel Anypoint ISS, and 3Com HomeClick
  • Proxy software - Wingate and Sygate
  • Security software - Norton Internet Security, Black Ice, and Zone Alarm
Check Browser and System Requirements

Verify that the customer's computers meet the following minimum requirements:
  • Browser Requirements
    • Windows: Microsoft Internet Explorer 5.5 or higher (included on the 2Wire CD), Netscape Navigator 4.7 or higher, or Firefox 1.0 or higher
    • Macintosh: Safari 1.0, Microsoft Internet Explorer 5.0, or Netscape 4.74 or higher
  • System Requirements
    • 5MB of available hard-disk space for the gateway software
    • Microsoft Windows 7, Windows Vista, Windows XP, Windows 2000, Windows NT 4.0 with Service Pack Windows ME, Windows 98/98SE, or Mac OS 8.6 or higher
    • Network adapter (e.g., Ethernet, USB, or 802.11b/g wireless)
While the browsers and operating systems (OS) listed above meet the minimum requirements, not all browsers and OS listed here fall within AT&T scope of support. Refer customers with browsers/OS not in our scope of support (available for U-verse Care only) to ConnecTech.
Choose a Computer and Connection Type
There are many ways to set up a network; typically, the first computer is located in the same room as the gateway and the U-verse connection. Ethernet is the preferred connection method for the first computer, although instructions for connecting via wireless are also provided. The first computer connected to the network is used to configure the gateway for proper operation. Save and close all open programs before beginning this process.
Note: Previous DSL customers may have filters installed. Confirm with customer that filters are still in all locations.
Filter Installation 
Regular telephone and U-verse HSI signals are carried over the same line. Converting a regular telephone line to U-verse can cause high-pitched tones and static when using the phone. Installing a filter on every telephone or telephone device sharing the same telephone number as the U-verse HSI separates these signals and eliminates the noise. Do not install filters if the telephone line is only carrying a U-verse HSI signal.
Install the U-verse HSI Filter
  1. Locate the phone jack where the gateway is located.
  2. Insert the U-verse HSI filter into the jack.
  3. If there is a phone, answering machine, fax machine, satellite TV equipment, or other phone device in this jack location, plug it into the filter port labeled PHONE.
  4. Install a filter on all other phone devices in the house (e.g., dial-up modems, fax machines, Caller ID devices, and receivers. Plug each of these devices into the filter port labeled PHONE. [Phone Jack - Screenshot]
For Wall-Mounted Phones
If the customer has a wall-mounted telephone, install a wall-mount filter following these steps:
  1. Lift the telephone from the wall pegs and disconnect the phone cord from the wall jack.
  2. Connect the telephone cord from the back of the filter into the wall jack. Align the keyhole slots on the filter with the wall plate pegs and press down gently to secure.
  3. Connect the telephone cord to the phone jack located on the front of the mounted filter.
  4. Attach the telephone to the mounting pegs on the filter and the installation is complete. [Wall Mount - Screenshot]
Ethernet Connection Instructions
  1. Connect the dual-port phone filter to their wall jack.
    • Phone service is not required to set up high-speed Internet.
  2. If the customer has a phone that shares this jack, plug it into the port labeled PHONE on the dual-port phone filter.
  3. Connect the green data cable from the port labeled DSL/HPNA on the dual-port filter to the phone line port on the gateway. [Setup View - Screenshot]
  4. Connect the yellow Ethernet cable from an Ethernet port on the gateway to the Ethernet port on the PC.
  5. Connect one end of the power adapter to the power port on the gateway and plug the other end into an electrical outlet. The customer should see a blinking then steady green power light.
    • The gateway is now powering up. Wait up to 15 minutes for the DSL and Internet indicator lights to be solid green and the Ethernet indicator light to be blinking green.
    • Do not unplug the power adapter or green data cable. Unplugging the gateway before power up is finished can damage the gateway. 
  6. If the DSL light does not turn solid green or continues to blink after 20 minutes, repeat the setup process, or try another phone jack in the home.


Activation 
  1. Have the customer turn on PC or Mac and open an Internet browser.
  2. The AT&T Online Registration page appears automatically. If it does not, have the customer type https://uverseactivation.att.com in the address line and continue with the online registration.
Wireless Connection
A wireless connection requires a wireless-enabled laptop or desktop computer with an 802.11b/g wireless network adapter installed.
Locate the Serial Number and Wireless Encryption Key
The serial number of the gateway is used as the network name (SSID). Beneath the serial number is a 10-digit number, which is used as the encryption key. These are located on the bottom of the gateway (shown in vertical orientation). This information is needed to configure the wireless adapter. [Serial Number and Wireless Encryption Key - Screenshot]
  • The network name is the word 2WIRE (in all capital letters), followed by the last three digits of the gateway's serial number (e.g., 2WIRE110).
  • In the future, all SSIDs may be increased to 10 characters in length (e.g., 2WIREXXXXX).
  • The sticker on the RG provides the correct SSID.
  • The encryption key is a 10-digit number located beneath the bar code on the bottom of the gateway. In the Serial Number screenshot above, it is 1234567891.
Note: For Mac OS X users, the $ character may need to be added at the beginning of the encryption key (e.g., $1234567891).
For operating system-specific wireless connection setup instructions, refer to:
Non-2Wire Wireless Adapter Configuration
The serial number of the gateway is used as the network name (SSID). Beneath the serial number is a 10-digit number, which is used as the encryption key. These are located on the bottom of the gateway (shown in vertical orientation). This information is needed to configure the wireless adapter. 
Configure the Adapter
  1. Install and configure the wireless adapter according to the manufacturer's instructions.
  2. Use the network adapter configuration software or Windows network-connection wizard to set the network name (SSID) and encryption key (WPA).
    • The network name is the word 2WIRE (in all capital letters), followed by a sequence of numbers (e.g., 2WIRE123 or 2WIRE12345).
    • The encryption key is a 64-bit hex value, located beneath the bar code on the bottom of the gateway.
    • For Mac OS X users, the $ character may need to be added at the beginning of the encryption key (e.g., $1234567891).


Additional Issues
Third-Party CPE and Bridge Mode 
Third-party routers are incompatible with the 2701HGV-B and should be removed prior to troubleshooting; 2701HGV-B cannot be put into Bridge mode. Placing the 2701HGV-B gateway in Bridge mode causes the device to be unable to authenticate and subsequently renders the customer without Internet connectivity. 
Broadband Link Unavailable Error 
The 2701HGV-B is capable of displaying diagnostic information on the customer's browser, in addition to displaying status via the LED lights. This section covers the Broadband Link Unavailable (No Sync) condition.
When the 2701HGV-B is unable to sync or maintain sync with the IP-DSL, two conditions occur: 
  1. The DSL LED blinks red to indicate that the device is attempting to sync/re-sync.
  2. Additionally, if the customer is currently browsing or attempts to browse and the device loses sync, the customer may encounter the error The Broadband Link is Currently Not Available. [The Broadband Link is Currently Not Available - Screenshot]
Run SCANR and follow the recommendations. 
Authentication Error
The 2701HGV-B is capable of displaying diagnostic information on the customer's browser, in addition to displaying status via the LED lights. This section covers the Broadband Authentication error (Unable to authenticate/obtain an IP).

When the 2701HGV-B is unable to authorize itself and pull down an IP address, the device exhibits the following: 
Run SCANR and follow the recommendations. If SCANR is down or unavailable, perform the following BAU troubleshooting steps: 
  1. Verify the customer is utilizing IP-DSL (identified with red letters at the Top of CRM). 
  2. Verify that the customer has a 2701HGV-B via G2. 
  3. Check account status/registration in the G2 LS Tool.
  4. Identify the issue. 
Firmware Upgrade Potential Issue
  1. If the customer does not have newest firmware 6.3.15.2, perform a reboot.
  2. If the firmware is:
    1. Upgraded, end the call
    2. Not upgraded, perform a factory reset
    3. Upgraded after the reset, end the call
  3. Send a new 2701 to replace the defective one and handle the replacement BAU if the customer has the old firmware after reset.
  4. Process a CPE swap via CRM/OMS with a due date for three business days from the time the order/request is made (e.g., if placing the order on September 10, 2013, the due date is November 13, 2012).
    • UPS does not deliver on weekends or holidays.
  5. Verify with the customer that someone is going to be available to accept the shipment at the service address provided or obtain an alternate shipping address. If applicable, update address on the shipping screen when placing the order.


LED Lights
TypeStatusDefinition
Power lightOff
The gateway is not getting power:
  1. Try a known good wall outlet.
  2. If a power strip is used, make sure it is switched on. 
  3. If power is not on, swap the CPE.
Blinking green (slow)The gateway is undergoing POST (power-on self test).
Solid greenPower is on.
Blinking orangeThe gateway is undergoing a software upgrade.
Solid redSystem error; contact Technical Support.
Ethernet, USB, or Wireless lightOffThe gateway is powered off or booting-up.
Solid greenDevice(s) is connected via Ethernet, USB, or wireless.
Flickering greenData traffic is coming into or going out from the network
DSL lightOffPowered off or booting-up
Blinking green (slow)Attempting to establish a connection to the broadband service
Blinking green (fast)Unable to connect to the DSL signal for more than three minutes
Solid greenConnected to the broadband service
Internet lightOffUnable to detect a DSL signal or the DSL signal is detected and the gateway is attempting to train
Blinking green (fast)Attempting to establish a connection to the broadband service
Solid redCannot connect to the broadband service

Install Cisco Linksys E1000 with Motorola 2210-02-1 IP-DSL Modem

Installation of the Motorola 2210 modem plus Cisco Linksys E1000 router can be accomplished via customer self-install (CSI) or full tech install (FTI) for services less than or equal to 6MB. 12MB and 18MB services require FTI. If the customer is upgrading services and receives a new CSI kit, ensure they install the Motorola 2210 received with the new kit.

Procedures
  1. Install and sync the Motorola 2210 modem before installing the Cisco E1000. 
  2. In order to verify that the Motorola 2210 is successfully connected, have the customer connect a PC to the Ethernet port of the Motorola 2210 and verify they can surf before configuring the tethered configuration. 
    • For this tethered configuration to function properly, use the Motorola 2210 firmware version 7.8.7r27.
  3. Install the Cisco E1000 following the manufacturer's literature provided in the installation kit.
  4. Verify the presence of the Cisco Linksys E1000 by looking in the Order Tree Product Configuration. [Product Tree - Screenshot]
Scope of Support
After validating connectivity with the Motorola 2210 and ensuring the customer can surf via the Ethernet connection on the back of the 2210 device, handle all other issues related to the E1000 as outlined below.

Connecting Wireless Devices to the Cisco E1000
Customers should use the E1000 Wi-Fi client on the Cisco installation CD provided with the device when configuring the Cisco E1000 to connect wireless devices. 
The Cisco E1000 comes with Wi-Fi Protected Setup (WPS) enabled on the device; however, using WPS to configure a wireless network can cause the customer to experience issues with connecting wireless devices to the Cisco E1000.

Additional Support
For additional information or support, refer the customer to Cisco/Linksys.
The Cisco Linksys E1000 router is a third-party device supported only by the vendor. Refer customers to Cisco/Linksys for online information or give them the contact numbers below for additional support or assistance.

Contact OptionsU.S. Customer ServiceU.S. Technical Support
Phone800-546-5797 (Option three)800-326-7114
Business hours
9:00 a.m. - 11:00 p.m. ET, Monday-Friday
11:00 a.m. - 8:00 p.m. ET, Saturday-Sunday
24/7; 365 days a year
Additional support http://support.linksys.com/en-us/support
To view customer collateral sent with the customer purchased equipment (CPE), refer to U-verse User Guides > select AT&T U-verse High Speed Internet > installation guide for 2210.
,

Motorola NVG589 Residential Gateway Wireless and Security Options

When the Wireless link on the Motorola NVG589 Residential Gateway RG (RG) interface is selected, the Wireless page appears. The Wireless page displays the status of the Motorola NVG589 wireless LAN elements. [Wireless General User Interface - Screenshot]
The center section of the Wireless page contains a summary of the wireless access point's (WAP) configuration settings and operational status. [Summary Information WAP - Screenshot]

The table below provides a description for each field:

FieldDescription
Network Name (SSID)
A preset number unique to the unit. Either leave it as-is or change it by entering a freeform name of up to 32 characters.
Example: Hercule's Wireless LAN. 
On client PC software, this might also be called the Network Name. The Wireless ID is used to identify this particular wireless LAN. Depending on their operating system or client wireless card, the customer must either:
  • Select from a list of available wireless LANs that appear in a scanned list on their PC (client).
  • Enter the name on their client in order to join the wireless LAN.
Hide SSID
  • If enabled, this mode hides the wireless network from the scanning features of the wireless client computers. 
  • Unless both the wireless clients and the RG share the same network name (SSID) in hidden mode, the RG's wireless LAN does not appear as an available network when scanned for by wireless-enabled computers. 
  • Members of the hidden WLAN must log onto the RG's wireless network with the identical SSID as that configured in the RG. 
  • Closed System mode is an ideal way to increase wireless security and to prevent casual detection by unwanted neighbors, office users, or malicious users such as hackers. 
  • If Hide SSID is not enabled, it is more convenient, but potentially less secure for clients accessing the WLAN by scanning available access points. Customers must decide based on their own network requirements.
Security, WPA Version, and WEP Key LengthSee Wireless Security for details.
Mode
  • The pull-down menu allows customers to select and lock the RG into the wireless transmission mode they want: B/G/N, B-only, B/G, G-only, or N-only.
  • For compatibility with clients using 802.11b (up to 11Mbps transmission), 802.11g (up to 20+ Mbps), 802.11a (up to 54Mbits using the 5GHz band), or 802.11n (from 54Mbits to 600Mbits with the use of four spatial streams at a channel width of 40MHz), select B/G/N. 
  • To limit the wireless LAN to one mode or the other, select G-only, N-only, or B-only, or some combination that applies.
Bandwidth
  • Can only be selected if mode is in some combination of 802.11n (from 54Mbits to 600Mbits with the use of four spatial streams at a channel width of 40MHz). 
  • Measure of the width of a range of frequencies, in megahertz.
Channel
  • The network broadcasts on channels 1-11 for North America. 
  • This is a frequency range is within the 2.4Ghz band. 
  • Channel selection depends on government regulated radio frequencies that vary from region-to-region. 
  • Channel selection can have a significant impact on performance, depending on other wireless activity close to this WAP.
  • Do not select a channel at any of the computers on the wireless network. They automatically scan available channels seeking an RG broadcasting on the SSID for which they are configured.
  • The Automatic setting allows the WAP to determine the best channel to broadcast automatically.
Power Level
  • Sets the wireless transmit power - Scales down the WAP's wireless-transmission coverage by lowering its radio power output.
  • Default is 100% power. 
  • Transmit power settings are useful in large venues with multiple wireless routers where customers want to reuse channels. Since there are only three non-overlapping channels in the 802.11 spectrum, it helps to size the WAP's cell to match the location. This allows customers to install a router to cover a small "hole" without conflicting with other routers nearby.
Wireless Protected Setup (WPS)
  • An easier way to use existing protocols to provide greater security for your wireless network connections. 
  • By default, Privacy is set to Wireless Protected Access (WPA-PSK). 
  • WPS allows customers to automatically generate a new strong WPA key for their RG and any client devices on their wireless network. 
    • Not all client wireless devices support WPS. 
    • The customer should refer to their documentation and then enter all the digits for the WPS PIN and click Submit. 
  • By default, Wireless Security is set to WPA-PSK with a pre-defined WPA-default key (WPA Pre-Shared Key).

Wireless Security
Other options are also available from the Security pull-down menu: [Wireless General User Interface Options - Screenshot]
FeatureDescription
WEP - Manual
  • WEP (Wired Equivalent Privacy) Security is a privacy option that is based on encryption between the router and any clients with wireless cards. 
  • If not using WPA-PSK Privacy, use WEP-encryption instead. 
    • For this encryption to work, both the WAP and each client must share the same wireless ID (SSID) and both must be using the same encryption keys.
  • WEP provides a level of data security by enabling encryption of network data. 
  • Customers can enable 40-bit or 128-bit WEP encryption (depending on the capability of their client wireless card) for IP traffic on the LAN.
  • Customers can enter their own encryption keys manually. This is a difficult process, but only needs to be done once. 
    • Customers should avoid the temptation to enter all the same characters.
WPA - PSK
  • Allows customers to enter their own key, the most secure option for their wireless network. The key can be between 8-63 characters, but for best security it should be at least 20 characters.
  • If WPA-PSK is selected as the privacy setting, the WPA Version pull-down menu allows customers to select the WPA version(s) that is required for client connections. Choices are: 
    • Both - For maximum interoperability
    • WPA-1 - For backward compatibility
    • WPA-2 - For maximum security
  • All clients must support the version(s) selected in order to successfully connect
  • Verify that the Wi-Fi client adapter supports this option. Not all Wi-Fi clients support WPA-PSK.
OFF - No Privacy
  • This mode disables privacy on the network, allowing any wireless users to connect to the wireless LAN. 
  • Use this option if using alternative security measures such as VPN tunnels, or if the network is for public use.
Key Length
  • The pull-down menu selects the length of each encryption key. 
  • The longer the key, the stronger the encryption and the more difficult it is to break the encryption. 
  • Enter a key using hexadecimal digits. For 40/64-bit encryption, use 10 digits; 26 digits for 128-bit WEP. Hexadecimal characters are 0–9, and a–f.
    Examples:
    • 40 bits: 02468ACE02
    • 128 bits: 0123456789ABCDEF0123456789
  • Any WEP-enabled client must have an identical key of the same length as the router, in order to successfully receive and decrypt the traffic. Similarly, the client also has a default key that it uses to encrypt its transmissions. 
    • In order for the router to receive the client's data, it must likewise have the identical key of the same length.

Advanced Firewall Configuration
The Motorola NVG589 Firewall Monitoring software and service is not offered by AT&T. If the customer requires Advanced Firewall Configuration, refer the customer to ConnecTech using WFE.